2017 wholesale price Expanded PTFE Tape Wholesale to French
2017 wholesale price Expanded PTFE Tape Wholesale to French Detail:
Expanded PTFE sealant tape possesses all the properties of PTFE, resistant to all the corrosive media.
Soft, twistable and bendable at will. Even if gravely rusted and worn out sealing face, as long as it is used, the equipment units may continue their service and the sealing can keep its best performance.
Excellent anti-wriggle variation ability and cold current resistance. Even in case of cross change of temperature and pressure, good sealing can be assured.
l Easy use and replacement
l Wide service scope.
Technical Data Sheet
|
No.
|
Project |
Technical Indexes |
|
1 |
PH Range |
0-14 |
|
2 |
Density |
0.7-0.8g/cm3 |
|
3 |
Temperature resistance |
-260-+260℃ |
|
4 |
High pressure resistance |
20~25Mpa |
|
5 |
Elongation |
20~30% |
|
6 |
Tensile strength |
30~35Mpa |
Regular Size
|
NO. |
SIZE |
NO. |
SIZE |
|
1 |
3mm*1.5mm*30m |
15 |
16mm*4mm*10m |
|
2 |
3mm*2mm*30m |
16 |
20mm*3mm*5m |
|
3 |
6mm*3mm*20m |
17 |
20mm*4mm*5m |
|
4 |
7mm*2.5mm*20m |
18 |
20mm*5mm*5m |
|
5 |
9mm*3mm*15m |
19 |
20mm*7mm*5m |
|
6 |
9mm*4mm*15m |
20 |
25mm*4mm*5m |
|
7 |
10mm*3mm*10m |
21 |
25mm*5mm*5m |
|
8 |
10mm*4mm*10m |
22 |
25mm*8mm*5m |
|
9 |
10mm*5mm*10m |
23 |
25mm*10mm*5m |
|
10 |
12mm*3mm*10m |
24 |
30mm*3mm*5m |
|
11 |
12mm*4mm*10m |
25 |
30mm*4mm*5m |
|
12 |
12mm*5mm*10m |
26 |
40mm*4mm*5m |
|
13 |
12mm*6mm*10m |
27 |
50mm*4mm*5m |
|
14 |
14mm*5mm*10m |
28 |
100mm*0.5mm*10m |
Application Area
It can be widely used in diverse pipelines to seal flanges, enameled products, glass, rubber products, plastics, non-rusting graphite lining tower, heat exchanger, pressure container as linings and to seal their flanges, to seal the fillers of diverse pumps and valves and to seal much heavy-calibre flanges which are not so precise, have larger unflat area and irregular shapes and require not too large tighting force.
Product detail pictures:
Related Product Guide:
What Is A PTFE Ring Gasket?
A Look at the Molded Gasket
2017 wholesale price Expanded PTFE Tape Wholesale to French, The product will supply to all over the world, such as: , , ,
About 9 hours of run in time on 5PSI.
Race spec full rebuild.
Engine mods only are:
HEAVILY Ported & Polished intake and exhaust runners (Flow tested and Port matched)
130lb Valve Springs
Replaced retainers, locks and seals
Valve seats cut
Full custom Cam (Total .562″ Intake, .593″ Exhaust)
Polished Alloy Valve Covers
1.7:1 Alloy Yella Terra Roller Rockers and Pushrods (very quite)
Rollmaster Double Row Timing Chain
OE-R Lifters
CUSTOM Cometic MLS Head Gaskets (Suited to 30PSI)
Acid Bathed and Ultrasonic cleaned block
Cryogenically hardened crank (by cryogen.com.au, very effective hardening process)
Fully balanced to 0.5 gram
ARP Head studs, ARP Main studs, ARP Big end bolts
ALL gaskets replaced with Factory standard or above
Balance shaft removed, dilled tapped oil feed
Cam, main and rod bearings (ALL Clevite, ALL TEFLON COATED)
JE Ceramic Coated and Forged Pistons
Forged Powdered Connecting Rods
Powerbond 5% overdrive harmonic balancer
Drilled main bearing oil feeds
Extensive Cooling and Oil Feed modifications
Machined oil pump cover
Casting smoothed oil pump and filter runners
High flow K&N oil filter
ALL Surfaces decked, Bored and Honed .020″ over
Cryogenically Hardened Block, Machine Rehoned after Hardening.
New Custom oil pump gears (hardened to increase longevity)
Custom Oil Pickup Tube
Fully Rebuilt and Recondition Supercharger
Custom Machined T6 Snout (YT lookalike) and Shaved to suit boost
Heavily ported/polished supercharger inlet and out
Inlet and outlet + port matched to heads LIM + Flow tested
Ported/Polished U-Bend
69.5mm Throttle Body
Custom externally vented PCV Breather system through supercharger
Plastic and Metal Center manufactures parts for medical, aerospace, electronic and military industries. Our services include; CNC Machining of metals and plastics i.e. titanium, aluminum, stainless steel, teflon, nylon, delrin, lexan, polycarbonate, peek, acetal. Plastic Injection Molding of engineered and commidity materials PP, HDPE, PC, ABS, Delrin, Nylon, Topaz. Plastic Fabrication, Plexiglass displays, acrylic stand, brochure holders, POP display, Counter top product showcase. Die Cutting of gaskets and seals like foam, cork, plastic, steel, bushing, washers
By from -
By from -
