China Manufacturer for Aflas O-Ring to Portland Factories

Short Description:

Aflas based synthetic rubber, reinforced with carbon black and peroxide cured. Has good rapid gas decompression(FGD) resistant properties, which making it suitable for many high pressure gas applications. Temperature capability for this type compound is +5~+200℃. Technical Data Sheet Properties Units Typical value Hardness IRHD 84 Tensile strength MPa 22 Elongation at break % 189 Modulus at50% elongation MPa 4 Modulus at100% elongation MPa 12  


Product Detail

Product Tags

Related Video

Feedback (2)

, , ,
China Manufacturer for Aflas O-Ring to Portland Factories Detail:

Aflas based synthetic rubber, reinforced with carbon black and peroxide cured. Has good rapid gas decompression(FGD) resistant properties, which making it suitable for many high pressure gas applications. Temperature capability for this type compound is +5~+200℃.

Technical Data Sheet

Properties Units Typical value
Hardness IRHD 84
Tensile strength MPa 22
Elongation at break % 189
Modulus at50% elongation MPa 4
Modulus at100% elongation MPa 12

 


Product detail pictures:

China Manufacturer for
 Aflas O-Ring to Portland Factories detail pictures


Related Product Guide:
What Is A PTFE Ring Gasket?
Useful Tips For Installing The Teflon Envelope Gasket

China Manufacturer for Aflas O-Ring to Portland Factories, The product will supply to all over the world, such as: , , ,


  • Automatic round ring bending machine
    1. Servo drive, high precision, length error less than +/-0.5mm
    2. High speed, linear feeding speed more than 40m/min
    3. Ring diameter: 35-750mm; 60-1000mm
    4. Wire gauge: 1-6mm; 2-8mm

    Please contact with Ms. Aileen for details:
    Tel: +86 513 8762 8369
    Fax: +86 513 8763 5890
    Skype: honeyaileen1
    Email: aileen@zhenhuan-machine.com



    Can’t find a replacement for that torn ribbon cable; don’t want to pay for a new one – solder splice the two bits – did you save them ?

    PLEASE NOTE: In the making of this video my efforts were necessarily clumsy because I could not take advantage of any magnification directly, especially using the microscope; I had to concentrate on aligning the cam to get a picture, so I was constrained to watching the screen of the VCR, it being too low resolution for productive effort. I would like to have used an eyepiece adaptor that fits both the camcorder and the ‘scope; then I should have been able to peer through the other eyepiece. So be assured it is a great deal easier than I make it look here. I have to admit that relatively few people have access to a stereo microscope; I paid around £180 ( ebay ) for this Russian made Lomo MBC-10, so at least it has been useful apart from being a toy.

    I use a Yihua [ goes under several trade names ] workstation that has a heater blower – like a hair drier but hotter and more concentrated flow of air – and a soldering iron that has, as an accessory, a very fine, needle point bit, allowing you to make a good job of such tiny amounts of solder, almost too small to see with the naked eye.

    The VX1000 mic/remote/cp flexiboard cable is about 1cm wide; with only a “normal” fine point soldering bit 40 joints were made in the space of approx 0.9 sq cm. The much finer bit was/is available as an optional accessory.

    See this video for demonstration of USB microscope: “ToddFun.com: USB Microscope Review”.

    Mario Parodi [ Guitar ] plays:-

    Albeniz: Rumores de la Caleta; SE-Op 165 – Malaguena
    Brahms: Cradle Song Op 49 no 4
    Debussy: Arabesca No 1; SB – Clair de lune


    5 Stars By from -

    5 Stars By from -

    Related Products