Factory best selling Expanded PTFE Tape to Jeddah Importers
Factory best selling Expanded PTFE Tape to Jeddah Importers Detail:
Expanded PTFE sealant tape possesses all the properties of PTFE, resistant to all the corrosive media.
Soft, twistable and bendable at will. Even if gravely rusted and worn out sealing face, as long as it is used, the equipment units may continue their service and the sealing can keep its best performance.
Excellent anti-wriggle variation ability and cold current resistance. Even in case of cross change of temperature and pressure, good sealing can be assured.
l Easy use and replacement
l Wide service scope.
Technical Data Sheet
|
No.
|
Project |
Technical Indexes |
|
1 |
PH Range |
0-14 |
|
2 |
Density |
0.7-0.8g/cm3 |
|
3 |
Temperature resistance |
-260-+260℃ |
|
4 |
High pressure resistance |
20~25Mpa |
|
5 |
Elongation |
20~30% |
|
6 |
Tensile strength |
30~35Mpa |
Regular Size
|
NO. |
SIZE |
NO. |
SIZE |
|
1 |
3mm*1.5mm*30m |
15 |
16mm*4mm*10m |
|
2 |
3mm*2mm*30m |
16 |
20mm*3mm*5m |
|
3 |
6mm*3mm*20m |
17 |
20mm*4mm*5m |
|
4 |
7mm*2.5mm*20m |
18 |
20mm*5mm*5m |
|
5 |
9mm*3mm*15m |
19 |
20mm*7mm*5m |
|
6 |
9mm*4mm*15m |
20 |
25mm*4mm*5m |
|
7 |
10mm*3mm*10m |
21 |
25mm*5mm*5m |
|
8 |
10mm*4mm*10m |
22 |
25mm*8mm*5m |
|
9 |
10mm*5mm*10m |
23 |
25mm*10mm*5m |
|
10 |
12mm*3mm*10m |
24 |
30mm*3mm*5m |
|
11 |
12mm*4mm*10m |
25 |
30mm*4mm*5m |
|
12 |
12mm*5mm*10m |
26 |
40mm*4mm*5m |
|
13 |
12mm*6mm*10m |
27 |
50mm*4mm*5m |
|
14 |
14mm*5mm*10m |
28 |
100mm*0.5mm*10m |
Application Area
It can be widely used in diverse pipelines to seal flanges, enameled products, glass, rubber products, plastics, non-rusting graphite lining tower, heat exchanger, pressure container as linings and to seal their flanges, to seal the fillers of diverse pumps and valves and to seal much heavy-calibre flanges which are not so precise, have larger unflat area and irregular shapes and require not too large tighting force.
Product detail pictures:
Related Product Guide:
O-Ring Sizes for Industrial Applications
A Look at the Molded Gasket
Factory best selling Expanded PTFE Tape to Jeddah Importers, The product will supply to all over the world, such as: , , ,
I built a physical deposition chamber, for now it’s just evaporative deposition but I plan on adding a few other variants. The thin films created can be used in many ways.
The chamber still has a ton of space leftover and I have some more equipment coming so hopefully I can do more interesting things.
Sorry there’s no footage of lathing the feedthroughs, they worked nice with a cut o-ring and some heat shrink. Make sure you cut a slot down the holding screw threads to vent behind em. The 2 copper feedthroughs allow (with a center tap) 2 tungsten boats with different metals so I can avoid opening the chamber in a multi layer coating.
The pump down takes about 45 min. to get to 10e-5. I can use a small steel hemisphere with a kf40 hose on the top for use with a secondary high vacuum chamber. The shutter was aluminum flashing with some steel stuck on one side so a neodymium magnet on the outside of the bell jar could move it around without a feedthrough.
This build was really fun
I got everything from mcmaster, K.j lesker, ebay and what I already had
This did cost a bit to make:
diffusion pump- $160
mechanical pump-$140
plate- $270 (ouch!)
valves- $90
gauges- $200
misc vacuum stuff -$120
bell jar – $140 (stupid)
other stuff – maybe $100?
I recommend you check out https://www.youtube.com/user/bkraz333
he has done some neat stuff with his setup and a bunch of other things
Warning: Something might be dangerous
Consider supporting me and my projects on patreon! https://www.patreon.com/Bennbuilds
By from -
By from -
