Manufactur standard Spiral Wound Gasket-R for Eindhoven Factory
Manufactur standard Spiral Wound Gasket-R for Eindhoven Factory Detail:
Spiral wound gasket consists of “V-shape”(or”W-shape”)metal tape and nonmetal tape, which are overlapped each other and wound continuously.To fasten the metal tape,both its start point and end point are tack welded.
Feature
Wide Scope of acceptable working conditions. Can be used under high temperature, high pressure and ultra-low temperature or vacuum conditions. Change the combination of the gasket materials is to tackle the chemical corrosion problem of diverse media toward the gasket.
Not very rigid requirements to the surface precision of the flange. May be used to seal flanges with rough surface
Easy installation and handy use.
Excellent Sealability
Products Type
echnical Data Sheet
|
Product&Type |
Size（mm） |
Temperature(℃) |
Pressure（Mpa） |
|
Spiral Wound Gasket filled with Graphite
|
φ16~φ3200 |
(In Oxidizing Environment )-240~+550℃；(In non-Oxidizing Environment)-240~+870℃ |
(Under hot water, oil etc. )30 Mpa; (Under vapor oil, gases etc.)20 Mpa |
|
Spiral Wound Gasket filled with Asbestos
|
φ16~φ3200 |
-150~+450℃ |
15 |
|
Spiral Wound Gasket filled with PTFE
|
φ16~φ3200 |
-200~+250℃ |
15 |
Application Area
The Spiral Wound Gaskets are mainly used in valves &pipes, pressure vessel, condenser, heat exchanger flanges in oil, chemical, metallurgy, vessel and mechanical industries.
Product detail pictures:
Related Product Guide:
A Look at the Molded Gasket
What Is A PTFE Ring Gasket?
Manufactur standard Spiral Wound Gasket-R for Eindhoven Factory, The product will supply to all over the world, such as: , , ,
TP Series 400
Table of contents:
Dismantling:
00:00 Dismantling the motor
02:07 Replacement of wear ring
03:59 Removal of impeller
05:32 Removal of shaft seal
06:40 Dismantling of pump head and cover
07:27 Removal of coupling
08:56 Dismantling stationary shaft seal part
Assembly:
09:51 Assembly stationary shaft seal part
11:05 Fitting the coupling
12:46 Fitting pump shaft
14:32 Assembly of pump head and cover
15:46 Fitting shaft seal 10 bar
17:08 Fitting shaft seal 25 bar
18:24 Fitting impeller
19:09 Fitting motor
Recorded: September 2004
For more information please visit:
https://www.grundfos.com/service-support.html
Until today the Whitworth Pipe Thread or in other words the joint sealing within the thread (according to EN 10226-1) has a high meaning in pipe work. Also piping systems using different joint techniques need the thread joint to connect valves, vessels, etc. Since 150 years Georg Fischer manufactures threaded malleable cast iron fittings. It is a pleasure for us to share our experience in the field of making thread joints. This video shows how to apply hemp and sealing paste properly on an external thread of a steel pipe and to connect it with our malleable cast iron fitting. With this video and some trials jour thread joints will as well keep performing 150 years.
Please also refer to our processing instructions of our Technical Catalogue, which is available electronically or as print version. Please consult www.fittings.at .
For thread joints made with other thread- or sealing-materials, the relevant technical conditions have to be taken into consideration, as well as the installation instruction of the related manufacturers.
Imprint:
https://www.fittings.at/content/gfps/traisen/en/service/footer/imprint.html
Disclaimer:
https://www.fittings.at/content/gfps/traisen/en/service/footer/disclaimer_gfps.html
By from -
By from -
