One of Hottest for PTFE Gasket Wholesale to Denmark

Short Description:

PTFE gasket is manufactured by molding method with PTFE granular resin. Compared with other plastic, PTFE has a superior properties against chemicals and temperature. Because of such excellent properties, PTFE gasket has a wide application as a sealing material. Technical Data Sheet Property Unit Result Density g/cm3 2.18 Elongation at Break % 200~450 Tensile Strength Mpa 14~18 Bending Strength Mpa No Break Pressure Resistance Mpa 24 Tensile Modulus Mpa 393 Bending Modulus ...


Product Detail

Product Tags

Related Video

Feedback (2)

, , ,
One of Hottest for PTFE Gasket Wholesale to Denmark Detail:

PTFE gasket is manufactured by molding method with PTFE granular resin. Compared with other plastic, PTFE has a superior properties against chemicals and temperature. Because of such excellent properties, PTFE gasket has a wide application as a sealing material.

Technical Data Sheet

Property Unit Result
Density g/cm3 2.18
Elongation at Break % 200~450
Tensile Strength Mpa 14~18
Bending Strength Mpa No Break
Pressure Resistance Mpa 24
Tensile Modulus Mpa 393
Bending Modulus Mpa 490~586
Working Temperature

(20000 hr, highest)

260

Application Area

As a sealing material, PTFE gaskets can be used in flange joint of various equipments and pipes in chemical industry, food producing industry, medicine industry and so on. It can bear the most bitter chemical medium, and has good anti-creeping performance. The unloaded operating temperature range is -180~+260℃.


Product detail pictures:

One of Hottest for
 PTFE Gasket Wholesale to Denmark detail pictures


Related Product Guide:
Comparison of O-Ring Materials
What Is A PTFE Ring Gasket?

One of Hottest for PTFE Gasket Wholesale to Denmark, The product will supply to all over the world, such as: , , ,


  • Can’t find a replacement for that torn ribbon cable; don’t want to pay for a new one – solder splice the two bits – did you save them ?

    PLEASE NOTE: In the making of this video my efforts were necessarily clumsy because I could not take advantage of any magnification directly, especially using the microscope; I had to concentrate on aligning the cam to get a picture, so I was constrained to watching the screen of the VCR, it being too low resolution for productive effort. I would like to have used an eyepiece adaptor that fits both the camcorder and the ‘scope; then I should have been able to peer through the other eyepiece. So be assured it is a great deal easier than I make it look here. I have to admit that relatively few people have access to a stereo microscope; I paid around £180 ( ebay ) for this Russian made Lomo MBC-10, so at least it has been useful apart from being a toy.

    I use a Yihua [ goes under several trade names ] workstation that has a heater blower – like a hair drier but hotter and more concentrated flow of air – and a soldering iron that has, as an accessory, a very fine, needle point bit, allowing you to make a good job of such tiny amounts of solder, almost too small to see with the naked eye.

    The VX1000 mic/remote/cp flexiboard cable is about 1cm wide; with only a “normal” fine point soldering bit 40 joints were made in the space of approx 0.9 sq cm. The much finer bit was/is available as an optional accessory.

    See this video for demonstration of USB microscope: “ToddFun.com: USB Microscope Review”.

    Mario Parodi [ Guitar ] plays:-

    Albeniz: Rumores de la Caleta; SE-Op 165 – Malaguena
    Brahms: Cradle Song Op 49 no 4
    Debussy: Arabesca No 1; SB – Clair de lune


    5 Stars By from -

    5 Stars By from -

    Related Products